How To Make A Homemade Curtain Rod

December 14, 2021 Post a Comment

Visit ashley @ 3 little greenwoods’s profile on pinterest. After you’ve chosen your branch, trim all the tiny twigs and sand the branch so it doesn’t ruin your curtains.

Step by Step How to make a flying broomstick curtain rod

Cut two small pieces of branch and secure them to the wall.

How to make a homemade curtain rod. The secret to bay window curtain rods. 10 homemade curtain rod you can make! When it comes to window treatments, the curtain rod doesn’t have to be just the necessary hardware.

They were 6″ long, which was a bit too long for my purposes. I may receive compensation in the form of monetary compensation or product compensation in exchange for my. To help you decide, i have some suggestions.

If you are looking for more ideas, you will love to have a look at these 16 diy curtains rods and hooks *. These diy copper curtain rods are both chic and affordable, and they are so so easy to make. Then you need this secret for bay window curtain rods.

How to make a wooden curtain rod bracket. Next spray it all down with a paint sprayer. This post contains affiliate links and/or is a sponsored post.

Instead of bending the rod, copper pipes are joined together to create a super sturdy window treatment. To start, use a drill and make a hole in the center of the rod, so your finial can screw into it. Step 2 mark on the wall the required location of the curtain rod, at the position of the center of the rod.

Hem curtains without sewing with iron on hem tape. Get those curtains hung and admire your work! Now cut the bracket to size with a miter saw on the 4 ½ mark.

Don’t forget to loop the curtain onto the branch before you take care of this last part. To hang the brackets, use painter’s tape to mark the top of the bracket and where each screw hole should be. Copper is such a beautiful accent, and curtain rods can be so expensive!

To create a custom diy curtain rod you’ll need to figure out how long to cut the rod. The materials make super inexpensive homemade curtain rods and the technique is easy as pie! Here’s another diy bay window curtain rod from julie blanner.

Using the 1 hole saw, drill through the wooden dowel. Read the full tutorial for how to make copper curtain rods. Mason jar window treatment from it all started with paint;

The materials for this project are pretty simple and inexpensive: See more ideas about curtain rods, home diy, home projects. Determine the size of the curtain rod.

Diy curtain rods for large windows. Predrill with a ⅛ drill bit onto the 3 mark made. Next, put the finial on part of the way, but not all of the way, so you can paint it easily.

This diy tutorial was inspired by lovely etc, and i had to give her tutorial a try plus she shares how to add finials to the diy curtain rod. Conclusion, you can use a lot of different materials to make curtain rods: My rod needed to be 113″.

Don’t forget to keep in mind the width of each of the finials sticking out on either side as well. The rod can have just as much style factor as the curtains themselves. Rope, cable, plastic pipes…i even seen some great recycled rods made out of a paddle or a fishing rod.

This curtain rod is for those who aren’t going to move curtains anywhere because here the curtains are fixed. Using a 1 ⅜ wooden dowel mark out two measurements. Thread the rod pocket, grommet or tab curtain onto the rod, arrange the gathers or folds evenly and set the rod in place, adjusting the curtain over the brackets.

I got these ones for about $3 a piece at home depot. Those decorative balls on the end of curtain rods are apparently called finials, and i used table legs to make them on these curtain rods. Easily mark the wall for the screws by using a piece of painters tape.

Read how to make it in the source. Then screw the main piece (with the curtain on) to these supports. The following diy curtain rods use a variety of materials that help.

If you’re using curtain rings (like mine), put them onto the rod now, followed by the elbows, then attach the other end of the elbows to the conduit fittings. I just measured the pipe and marked where i needed to cut with a sharpie. Once the floor flanges are securely in place, screw the conduit fittings into the floor flanges.

Mark 3 from the end for the hole and 4 ½ for the final cut. These are a great alternative to the high prices of rods for large windows. Before jumping into making your homemade curtain rod, you need to decide how wide you want your curtain rod to be.

How to Make Inexpensive, Fabulous, Custom Corner Drapery